Start with the fitting size, not the filter
The DeatschWerks 70mm Billet Fuel Filter Regulator is built around 5/16-inch inlet and outlet fittings. That single specification should drive your first decision: whether your existing fuel lines and connections are set up for 5/16-inch hardware. If they are not, you are planning an adapter strategy before you plan the mounting location.
This unit combines a 10-micron filter element and a pressure regulator in one 70mm billet aluminum housing. That packaging saves space and simplifies plumbing compared with separate components, but it also means the filter and regulator share one service location. Plan access to that location before you cut or bend any line.
What the catalog confirms about this unit
- 70mm Billet Fuel Filter Regulator 10 Micron with 5/16in Fittings: 5/16-inch inlet and outlet fittings for compatibility with standard fuel lines This is the connection standard you must match before anything else; it determines whether the unit drops into your current plumbing or needs adaptation.

70mm Billet Fuel Filter Regulator 10 Micron with 5/16in Fittings - 70mm Billet Fuel Filter Regulator 10 Micron with 5/16in Fittings: 10-micron filtration element helps protect downstream fuel components The filtration rating is part of the product's function, so replacement and service planning should account for a 10-micron element rather than a generic filter.
- 70mm Billet Fuel Filter Regulator 10 Micron with 5/16in Fittings: 70mm billet aluminum housing for strength and heat dissipation The housing size and material affect mounting space and how the unit fits in an engine bay or chassis area.
A practical order of work for the 5/16-inch setup
- 1. Confirm your line ends are 5/16-inch compatible: The catalog specifies 5/16-inch inlet and outlet fittings. Check the hard line, hose end, or adapter you intend to connect. If your system uses a different size, resolve that mismatch with the correct adapter before mounting the unit.
- 2. Choose a mounting location with service access: Because the filter and regulator are one assembly, you will need room to reach the unit for filter service. The catalog does not supply mounting dimensions or a bracket pattern, so verify clearance against the 70mm housing in your own layout.
- 3. Plan the flow direction before cutting line: The product description identifies inlet and outlet fittings but does not state a required orientation in the supplied record. Confirm the intended flow path for your system and route lines so the inlet and outlet are not crossed.
- 4. Leave the pressure setting to verified instructions: The supplied catalog does not include a pressure adjustment procedure, target pressure, or regulator set screw details. Do not guess at a setting; use the instructions that come with the unit or confirm the correct procedure for your application.
- 5. Treat the first run as a check, not a finish: After plumbing is complete, check for leaks and confirm the filter housing is secure. The catalog does not provide torque values or a leak-test procedure, so follow the manufacturer's documentation rather than a generic number.
Where the 10-micron element changes your maintenance plan
A 10-micron element is a deliberate choice: it is fine enough to protect downstream components, and that protection depends on the element being in good condition. The catalog confirms the filtration rating but does not list a replacement interval, a part number for the element, or a service procedure. Those details need to come from the product documentation or DeatschWerks directly.
Practically, that means you should decide now how you will access the unit for service. A regulator that is easy to adjust but buried behind a crossmember is a poor installation. The combined housing is compact, but compact is not the same as serviceable.
Combined unit versus separate filter and regulator
The tradeoff is straightforward. A combined unit reduces the number of plumbing connections and the space needed for two separate components. Separate components give you more freedom to place the filter and regulator independently and to service one without disturbing the other.
- Combined 70mm unit: One housing, one set of 5/16-inch connections, and one service location. Fewer joints can mean fewer potential leak points, but filter service and regulator access are tied together.
- Separate filter and regulator: More plumbing and more space required, but you can position each component for its own service needs. This can matter if your chassis has limited access to a single combined location.
What the catalog does not settle before you order
The supplied information confirms the 5/16-inch fittings, the 10-micron element, the 70mm billet aluminum housing, and the combined filter-regulator function. It does not confirm a specific pressure range, a mounting bracket, a replacement filter part number, or a vehicle-specific fitment list. Those are legitimate questions to resolve with DeatschWerks or your builder before purchase.
That is not a reason to avoid the product; it is a reason to treat the catalog as a starting point for the fitment conversation. If your fuel system already uses 5/16-inch lines and you want filtration and regulation in one compact location, this unit is aimed at that job. If you need a different line size or a documented pressure setting out of the box, confirm those details first.


